Category: Fire Alarm System

Showing 97–112 of 564 results

• 

  wishlist

  C-TEC CFP Network Driver Card CFP761

  CFP Network Driver Card Part No. CFP761 An optional system expansion device for use with CFP Standard and CFP AlarmSense conventional fire panels. Allows the connection of up to eight CFP760 Repeaters (one CFP761 required per Main, all CFP760 repeaters include a CFP761 as standard). Communicates over screened two-wire fire resistant cable. Total repeater network cable length should …

  C-TEC CFP Network Driver Card CFP761Read More

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (2 Output Per Zone Relays)

  • An optional system expansion device for use with CFP702-4 Standard 2 Zone Fire Panels or CFP702-2 AlarmSense 2 Zone Fire Panels.
  • Provides two output per zone relays which will changeover when the corresponding zone is in alarm (subject to certain conditions – for full details refer to the instructions, downloadable below).

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (4 Output Per Zone Relays)

  • An optional system expansion device for use with CFP704-4 Standard 4 Zone Fire Panels or CFP704-2 AlarmSense 4 Zone Fire Panels.
  • Provides four output per zone relays which will changeover when the corresponding zone is in alarm (subject to certain conditions – for full details refer to the instructions, downloadable below).
  • PCB mounts inside the CFP fire panel.
  • Outputs are NOT designed to switch mains voltages

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (8 Output Per Zone Relays)

  • An optional system expansion device for use with CFP708-4 Standard 8 Zone Fire Panels or CFP708-2 AlarmSense 8 Zone Fire Panels.
  • Provides eight output per zone relays which will changeover when the corresponding zone is in alarm (subject to certain conditions – for full details refer to the instructions, downloadable below).
  • PCB mounts inside the CFP fire panel.
  • Outputs are NOT designed to switch mains voltages.

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote & 8 Output Per Zone Relays) CFP763

  • An optional system expansion device for use with CFP Standard 2-8 Zone Fire Panels or CFP AlarmSense 2-8 Zone Fire Panels.
  • Provides four panel-controlled volt free relay outputs (reset, fault, aux. fire and remote) and eight output per zone relays.
  • PCB mounts inside the CFP fire panel.

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote Relay Outputs)

  • Product dimensions (mm)	82 W x 125 H x D 23mm.
    Weight	64g.
    Properties	Single pole changeover contacts; Rated at 1A 50V; 50V Isolation between relays, contacts and CFP & relays; 27mA active relay coil current @ 27.6V supply.

  Read more
• 

  wishlist

  C-TEC CFP Standard 2 Zone Conventional Fire Alarm Panel Part No. CFP702-4

  ₦65,000.00

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB)
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry
  • Manufactured by C-TEC in the UK
  • Eight detector zone circuits
  • Four conventional sounder circuits
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU
  • Wide range of test and fault-finding facilities
  • Four open-collector outputs (Fire, Fault, Remote and Reset)
  • ‘Class change’ and alert inputs
  • Installer-friendly design
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required
  • Low 25mA quiescent current
  • Multiple indicators
  • No system expansion connections
  • Fully compatible with C-TEC’s ActiV range of conventional fire detectors

  Add to cart
• 

  wishlist

  C-TEC CFP Standard 4 Zone Conventional Fire Alarm Panel Part No. CFP704-4

  ₦73,000.00

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB)
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry
  • Manufactured by C-TEC in the UK
  • Eight detector zone circuits
  • Four conventional sounder circuits
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU
  • Wide range of test and fault-finding facilities
  • Four open-collector outputs (Fire, Fault, Remote and Reset)
  • ‘Class change’ and alert inputs
  • Installer-friendly design
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required
  • Low 25mA quiescent current
  • Multiple indicators
  • No system expansion connections
  • Fully compatible with C-TEC’s ActiV range of conventional fire detectors

  Add to cart
• 

  wishlist

  C-TEC CFP Standard 8 Zone Conventional Fire Alarm Panel Part No. CFP708-4

  ₦96,000.00

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB)
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry
  • Manufactured by C-TEC in the UK
  • Eight detector zone circuits
  • Four conventional sounder circuits
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU
  • Wide range of test and fault-finding facilities
  • Four open-collector outputs (Fire, Fault, Remote and Reset)
  • ‘Class change’ and alert inputs
  • Installer-friendly design
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required
  • Low 25mA quiescent current
  • Multiple indicators
  • No system expansion connections
  • Fully compatible with C-TEC’s ActiV range of conventional fire detectors

  Add to cart
• 

  wishlist

  C-TEC Conventional Sounder Isolator Controller Part No. BF365SC

  • Designed to meet requirement 17.9.2c of Dutch standard NEN2575.
  • BSI certified to EN54 parts 17 & 18.
  • Easily interfaced to a conventional fire alarm sounder circuit.
  • Allows low-cost, non-fire resistant sounder circuit cabling to be used when used in conjunction with our BF365IM Isolator Modules (subject to fire officer approval).
  • Wiring must be made in a loop arrangement, beginning and ending at the controller.
  • If a wiring fault should occur, the Module(s) nearest to the faulty section of cabling will, if needed, isolate this section. As the Modules are driven from each direction, any loss of cable integrity will have no effect on the functionality of the actual sounders.
  • Fits on standard UK 25mm flush or surface mount back boxes

  • Download datasheet

  Read more
• 

  wishlist

  C-TEC Double Gang Surface Interface Plate, deep (33mm) Part No. NCP-26

  • Allows standard UK double gang plated products to be fixed to most European style back boxes (square and round variants).

  • Adapts to most European fixing centres – see video for further details.
  • Multiple variants available – options include single gang shallow (NCP-23), single gang deep (NCP-24), double gang shallow (NCP-25) and double gang deep (NCP-26).
  • Designed to match C-TEC’s existing plastics and colours.
  • Tough and durable.
  • Can also be surface mounted directly to a wall.

  • • Download datasheet

  Read more
• 

  wishlist

  C-TEC Double Gang Surface Interface Plate, shallow (20mm) Part No. NCP-25

  • Allows standard UK double gang plated products to be fixed to most European style back boxes (square and round variants).
  • Adapts to most European fixing centres – see video for further details.
  • Multiple variants available – options include single gang shallow (NCP-23), single gang deep (NCP-24), double gang shallow (NCP-25) and double gang deep (NCP-26).
  • Designed to match C-TEC’s existing plastics and colours.
  • Tough and durable.
  • Can also be surface mounted directly to a wall.

  Download datasheet

  Read more
• 

  wishlist

  C-TEC Economy Status Unit Part No. EP211

  ₦59,000.00

  • • • Designed to connect to the EP203 Automatic Extinguisher Panel to provide remote system status indication via three LEDs.
      • Includes a mode (auto/manual) keyswitch.
      • Mounts on a standard UK single gang 25mm flush or surface back box.
      • Max. 8 economy status units per EP203 panel.
      • Download datasheet

  Add to cart
• 

  wishlist

  C-TEC EFP1 Single Zone Conventional Fire Alarm Panel Part No. FF380-2

  ₦47,000.00

  • • Installer-friendly design.
    • Robust metal enclosure with heavy-duty base connections.
    • One conventional Zone circuit
    • Two conventional Sounder circuits.
    • Separate indicators for open & short circuit fault, sounder fault and battery/power supply fault.
    • Non-latching class change sounder output, latching fire & non-latching fault outputs (via optional expansion loom).
    • Short circuit=fire facility (pre-1980 BS, no resistors in call points, selectable on a zone by zone basis).
    • Multi-lingual variants (subject to quantities).
    • Space for 2 x 12V 2.3Ah VRLA batteries.
    • Compatible with virtually all known conventional fire detectors including C-TEC’s ActiV range.
    • Designed to comply with BS 5839-4 (this panel in not compliant with EN54-2/4 and should NOT be used in new UK or European installations).
    • Download datasheet

  Add to cart
• 

  wishlist

  C-TEC EP203 Automatic Extinguisher Panel Part No. EP203

  ₦169,000.00

   

  Technical Specifications
  Approvals/certifications Certified to EN12094-1 and EN54-2 & 4 by the LPCB.
  Mains supply 230V 50/60Hz.
  Mains rated current 810mA max.
  Internal power supply 19V-28.5V (27V nominal). Ripple 7V maximum (battery fault).
  Total output current limited to 1.5A @ 230Vac continuous, 3A peak (ImaxA eq 800mA).
  Quiescent current 40mA (on mains fail). Zone quiescent 2mA max.
  Max battery size and type 2 x 12V 7Ah VRLA connected in series.
  No. of detector zone circuits 3 @ 19-28Vdc (Max. length per circuit is 250m).
  Max. devices per detector zone 20 detectors (or 32 detectors/manual call points combined).
  No. of conventional sounder circuits 3 (two x 1st stage; one x 2nd stage). Max. length per circuit is 50m).
  EOL resistor value 6800 5% Tol. 0/25W (blue, grey, red, gold).
  Max. sounder output current 3 x 200mA.
  Auxiliary relays Six: (1) Fire; (2) Local Fire; (3) Extract Fan; (4) 1st Stage; (5) 2nd Stage; (6) Fault. Volt free single pole
  changeover. Max. switch current 1A; Max. switch voltage 30Vdc. Five additional relays available via
  EP212 relay card.
  Other outputs Extinguishant release (21-28Vdc, rated at 1A for 5 mins). Programmable to delay by 0-60 seconds; to
  be active for 1-300 seconds and to flood for 60-1800 seconds.
  Auxiliary inputs Six: (1) Manual Release; (2) Flow Switch; (3) Low Pressure; (4) Mode; (5) Hold; (6) Abort. 8K-2K normal;
  1.8K-200 active; 150-0 short circuit. EOL value: 6K8 +/-5%, 0.25W.
  Indicators Multiple indicators are provided – refer to the EP203 instructions for details.
  Controls Extinguishant release (housed in yellow casing); Accessed keyswitch; Operation keyswitch (Manual
  only or Manual & Auto); Buttons for Menu; Silence internal sounder; reset panel; silence/resound
  sounders and scrolling.
  Expansion connections Yes – for up to 8 x Remote status units (2 wire RS485 + 2 wire power) and/or up to 8 x Ecomomy
  status units (2 wire power + 2 wire mode select).
  Product dimensions (mm) 439 W x 276 H x 70 D mm (back box); 467 W x 293 H x 29 D mm (lid).
  Construction & finish Metal back box; metal chassis’ plastic lid.
  IP Rating IP30.
  Weight 4.2kg (without batteries).
  Operating conditions/temperature -5°C to +40°C. Max relative humidity: 95%

   

   

  Add to cart
• 

  wishlist

  C-TEC Extinguishant Hold off/Abort Button Part No. EP215

  • • • A surface or flush mounting hold or abort button designed to connect to an EP203 automatic extinguisher panel to provide a means of delaying or cancelling the extinguishant release sequence.
      • Comprises a 35mm black back box, yellow lid and green push button.
      • Supplied with two branding label options (‘Extinguishant Hold Off’ and ‘Extinguishant Abort’).
      • Actual operation depends on wiring configuration (if hold and abort functions are required, at least two EP215 buttons will be needed).
      • IP24 rated (indoor use only).
      • Download datasheet

  Read more