Popular
Zeta ZAIO/230 Mains IO 1 Channel Input/Output Module – Fyreye MKII Protocol – 8A @ 230V AC
The Mains IO Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the Fire Alarm Control panel using normally open dry contact connections.
Zeta ZAIO/230 Mains IO 1 Channel Input/Output Module – Fyreye MKII Protocol – 8A @ 230V AC
The Mains IO Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the Fire Alarm Control panel using normally open dry contact connections.
The connection to the input is monitored for fault (open or short circuit) and Alarm conditions.
The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System, for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing systems, etc.
Module is provided with a loop short-circuit isolator and with a voltage free single pole change over mains rated output. The output relay is always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an on-board red LED.
An 8-way D.I.L switch is provided to configure the module’s address. This value can be set in the range 1 to 125.
The following programmable functions are available: Input Activation Mode, Delayed Input Alarm Activation, Output Delayed Activation.
The Simplicity CO 8 range is designed to detect & monitor CO concentrations in places such as warehouses, car parks, tunnels and enclosed buildings where forklifts, cars and delivery trucks can produce deadly amounts of carbon monoxide, in high traffic areas Carbon Monoxide can accumulate in these areas and can be a serious safety and health concern.
Key Features
- Fast Activation Response
- Loop Powered
- Five Status LEDs provided
- Low Power Consumption
- Module features an integral short-circuit loop isolator
- Single mains rated relay contact
| Dimensions | 9 × 15 × 0.45 cm |
|---|
Related products
-
Gent by Honeywell VESDA-E VEA(VER-A40-40-STX)
Read moreDESCRIPTION
The VESDA-E VEA series of detectors
combine VESDA reliability and early warning smoke detection with pinpoint addressability and a variety of annunciation options that truly surpass traditional spot detectors.COLOUR LCD DISPLAY
The VEA-040-A10 detector features a 3.5” colour LCD display which provides a range of status information including alarm and fault conditions as well as smoke level. Screens for each type of information are available using a simple navigation system.
VESDAnet™
VESDA detectors and devices communicate on VESDAnet which provides a
robust bi-directional communication network allowing continued redundant operation even during single point wiring failures. VESDAnet enables primary reporting, centralized configuration, control, maintenance and monitoring.
ETHERNET AND WIFI CONNECTIVITY
VESDA-E detectors offer Ethernet and WiFi connectivity as standard features. The detector can be added to a corporate network, allowing WiFi enabled tablet devices and laptops installed with Xtralis configuration software to connect
wirelessly to the detector via the network.
The VESDA-E VEA series of detectors
combine VESDA reliability and early warning smoke detection with pinpoint addressability and a variety of annunciation options that truly surpass traditional spot detectors -
Zeta Fyreye MkII Conventional Heat Detectors MKII-HF/CS90
₦9,500.00Add to cartDESCRIPTION
The Fyreye Rate of Rise heat detectors (MKII-HFCS90) use a thermistor arrangement to sense a quick rise in
temperature and also a final threshold temperature of 90°C. The Fyreye fixed heat detector (MKII-HF/CS90) has a single thermistor arrangement that gives an alarm at a temperature of 90°C.
There are 4 types of mounting base available; standard or deep and with or without diode. -
APOLLO GREEN INTELLIGENT MANUAL CALL POINT (SA5900-906APO)
Read moreThe Manual Call Point is commonly used to manually release secure doors or barriers in the event of emergency.
- Resettable operating element
- 170° viewable LED
- Suitable for semi flush or surface mounting
- ‘Plug and Play’ terminal connections for faster wiring
- Continuity link for wiring test before commissioning
- XP95, Discovery and CoreProtocol compatible
-
Gent Surface MCP (XENS-805) 470 Ohms Re-settable
₦10,000.00Add to cartGent XENS-805 Surface MCP 470 Ohms Re-settable Gent Surface MCP (XENS-805) 470 Ohms Re-settable requires no hammer and is easy and safe to operate. Gent’s conventional manual call points are designed to provide a manual alarm interface to conventional fire alarm control panels. All call points are supplied in the standard red colour and are …
Know Us
Safetech.hub is the newest online platform envisioned to provide 24/7 online platform for integrators, installers, and end users of Extra Low Voltage (ELV) systems in Nigeria
Read More
Reviews
There are no reviews yet.