Archives: Shop

Showing 97–112 of 733 results

• 

  wishlist

  C-TEC CFP 8 Zone Repeater Panel

  ₦96,000.00

  • Can be used to repeat the functions of a master CFP standard or AlarmSense 2-8 zone fire panel at remote parts of site (e.g. all potential fire service entrances).
  • Up to 8 repeaters per CFP master.
  • Includes its own Mains power supply that requires its own standby battery supply.
  • Provides the user with access to all AL1 and AL2 functions.
  • Master/Repeater communication achieved using CFP761 network driver cards (one CFP761 is supplied with the Repeater, an additional CF761 card is required at the master CFP).
  • Communicates over screened two-wire fire resistant cable.
  • Total repeater network cable length should not exceed 1KM.
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required.

  Add to cart
• 

  wishlist

  C-TEC CFP 8 Zone Repeater Panel Part No. CFP760

  ₦100,000.00

  • • Can be used to repeat the functions of a master CFP standard or AlarmSense 2-8 zone fire panel at remote parts of site (e.g. all potential fire service entrances).
    • Up to 8 repeaters per CFP master.
    • Includes its own Mains power supply that requires its own standby battery supply.
    • Provides the user with access to all AL1 and AL2 functions.
    • Master/Repeater communication achieved using CFP761 network driver cards (one CFP761 is supplied with the Repeater, an additional CF761 card is required at the master CFP).
    • Communicates over screened two-wire fire resistant cable.
    • Total repeater network cable length should not exceed 1KM.
    • Attractive flush or surface mountable plastic lid and enclosure – no bezel required.
    • Download datasheet

  Add to cart
• 

  wishlist

  C-TEC CFP AlarmSense 2 Zone Two-Wire Fire Alarm Panel

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB).
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry.
  • Manufactured by C-TEC in the UK.
  • Two AlarmSense zone circuits – compatible with Apollo’s AlarmSense detectors, call points, sounders and visual indicators.
  • Four conventional sounder circuits.
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU.
  • Wide range of engineering functions including zone test, coincidence, zone delay and non-latching zones.
  • Two on-board relays (Fire and Fault).
  • Two open-collector outputs (Remote and Reset).
  • ‘Class change’ and alert inputs.
  • Installer-friendly design.
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required.
  • Low 25mA quiescent current.
  • Multiple indicators.
  • System expansion connections provided for up to eight two-wire repeaters (one CFP761 network card required per system).
  • Space for two x 12V 3.3Ah VRLA batteries.

  Read more
• 

  wishlist

  C-TEC CFP AlarmSense 4 Zone Two-Wire Fire Alarm Panel

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB).
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry.
  • Manufactured by C-TEC in the UK.
  • Two AlarmSense zone circuits – compatible with Apollo’s AlarmSense detectors, call points, sounders and visual indicators.
  • Four conventional sounder circuits.
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU.
  • Wide range of engineering functions including zone test, coincidence, zone delay and non-latching zones.
  • Two on-board relays (Fire and Fault).
  • Two open-collector outputs (Remote and Reset).
  • ‘Class change’ and alert inputs.
  • Installer-friendly design.
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required.
  • Low 25mA quiescent current.
  • Multiple indicators.
  • System expansion connections provided for up to eight two-wire repeaters (one CFP761 network card required per system).
  • Space for two x 12V 3.3Ah VRLA batteries.

  Read more
• 

  wishlist

  C-TEC CFP AlarmSense 8 Zone Two-Wire Fire Alarm Panel

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB).
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry.
  • Manufactured by C-TEC in the UK.
  • Eight AlarmSense zone circuits – compatible with Apollo’s AlarmSense detectors, call points, sounders and visual indicators.
  • Four conventional sounder circuits.
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU.
  • Wide range of engineering functions including zone test, coincidence, zone delay and non-latching zones.
  • Two on-board relays (Fire and Fault).
  • Two open-collector outputs (Remote and Reset).
  • ‘Class change’ and alert inputs.
  • Installer-friendly design.
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required.
  • Low 25mA quiescent current.
  • Multiple indicators.
  • System expansion connections provided for up to eight two-wire repeaters (one CFP761 network card required per system).
  • Space for two x 12V 3.3Ah VRLA batteries.

  Read more
• 

  wishlist

  C-TEC CFP Network Driver Card CFP761

  CFP Network Driver Card Part No. CFP761 An optional system expansion device for use with CFP Standard and CFP AlarmSense conventional fire panels. Allows the connection of up to eight CFP760 Repeaters (one CFP761 required per Main, all CFP760 repeaters include a CFP761 as standard). Communicates over screened two-wire fire resistant cable. Total repeater network cable length should …

  C-TEC CFP Network Driver Card CFP761Read More

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (2 Output Per Zone Relays)

  • An optional system expansion device for use with CFP702-4 Standard 2 Zone Fire Panels or CFP702-2 AlarmSense 2 Zone Fire Panels.
  • Provides two output per zone relays which will changeover when the corresponding zone is in alarm (subject to certain conditions – for full details refer to the instructions, downloadable below).

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (4 Output Per Zone Relays)

  • An optional system expansion device for use with CFP704-4 Standard 4 Zone Fire Panels or CFP704-2 AlarmSense 4 Zone Fire Panels.
  • Provides four output per zone relays which will changeover when the corresponding zone is in alarm (subject to certain conditions – for full details refer to the instructions, downloadable below).
  • PCB mounts inside the CFP fire panel.
  • Outputs are NOT designed to switch mains voltages

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (8 Output Per Zone Relays)

  • An optional system expansion device for use with CFP708-4 Standard 8 Zone Fire Panels or CFP708-2 AlarmSense 8 Zone Fire Panels.
  • Provides eight output per zone relays which will changeover when the corresponding zone is in alarm (subject to certain conditions – for full details refer to the instructions, downloadable below).
  • PCB mounts inside the CFP fire panel.
  • Outputs are NOT designed to switch mains voltages.

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote & 8 Output Per Zone Relays) CFP763

  • An optional system expansion device for use with CFP Standard 2-8 Zone Fire Panels or CFP AlarmSense 2-8 Zone Fire Panels.
  • Provides four panel-controlled volt free relay outputs (reset, fault, aux. fire and remote) and eight output per zone relays.
  • PCB mounts inside the CFP fire panel.

  Read more
• 

  wishlist

  C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote Relay Outputs)

  • Product dimensions (mm)	82 W x 125 H x D 23mm.
    Weight	64g.
    Properties	Single pole changeover contacts; Rated at 1A 50V; 50V Isolation between relays, contacts and CFP & relays; 27mA active relay coil current @ 27.6V supply.

  Read more
• 

  wishlist

  C-TEC CFP Standard 2 Zone Conventional Fire Alarm Panel Part No. CFP702-4

  ₦65,000.00

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB)
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry
  • Manufactured by C-TEC in the UK
  • Eight detector zone circuits
  • Four conventional sounder circuits
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU
  • Wide range of test and fault-finding facilities
  • Four open-collector outputs (Fire, Fault, Remote and Reset)
  • ‘Class change’ and alert inputs
  • Installer-friendly design
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required
  • Low 25mA quiescent current
  • Multiple indicators
  • No system expansion connections
  • Fully compatible with C-TEC’s ActiV range of conventional fire detectors

  Add to cart
• 

  wishlist

  C-TEC CFP Standard 4 Zone Conventional Fire Alarm Panel Part No. CFP704-4

  ₦73,000.00

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB)
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry
  • Manufactured by C-TEC in the UK
  • Eight detector zone circuits
  • Four conventional sounder circuits
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU
  • Wide range of test and fault-finding facilities
  • Four open-collector outputs (Fire, Fault, Remote and Reset)
  • ‘Class change’ and alert inputs
  • Installer-friendly design
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required
  • Low 25mA quiescent current
  • Multiple indicators
  • No system expansion connections
  • Fully compatible with C-TEC’s ActiV range of conventional fire detectors

  Add to cart
• 

  wishlist

  C-TEC CFP Standard 8 Zone Conventional Fire Alarm Panel Part No. CFP708-4

  ₦96,000.00

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB)
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry
  • Manufactured by C-TEC in the UK
  • Eight detector zone circuits
  • Four conventional sounder circuits
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU
  • Wide range of test and fault-finding facilities
  • Four open-collector outputs (Fire, Fault, Remote and Reset)
  • ‘Class change’ and alert inputs
  • Installer-friendly design
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required
  • Low 25mA quiescent current
  • Multiple indicators
  • No system expansion connections
  • Fully compatible with C-TEC’s ActiV range of conventional fire detectors

  Add to cart
• 

  wishlist

  C-TEC Conventional Sounder Isolator Controller Part No. BF365SC

  • Designed to meet requirement 17.9.2c of Dutch standard NEN2575.
  • BSI certified to EN54 parts 17 & 18.
  • Easily interfaced to a conventional fire alarm sounder circuit.
  • Allows low-cost, non-fire resistant sounder circuit cabling to be used when used in conjunction with our BF365IM Isolator Modules (subject to fire officer approval).
  • Wiring must be made in a loop arrangement, beginning and ending at the controller.
  • If a wiring fault should occur, the Module(s) nearest to the faulty section of cabling will, if needed, isolate this section. As the Modules are driven from each direction, any loss of cable integrity will have no effect on the functionality of the actual sounders.
  • Fits on standard UK 25mm flush or surface mount back boxes

  • Download datasheet

  Read more
• 

  wishlist

  C-TEC Double Gang Surface Interface Plate, deep (33mm) Part No. NCP-26

  • Allows standard UK double gang plated products to be fixed to most European style back boxes (square and round variants).

  • Adapts to most European fixing centres – see video for further details.
  • Multiple variants available – options include single gang shallow (NCP-23), single gang deep (NCP-24), double gang shallow (NCP-25) and double gang deep (NCP-26).
  • Designed to match C-TEC’s existing plastics and colours.
  • Tough and durable.
  • Can also be surface mounted directly to a wall.

  • • Download datasheet

  Read more