GENT NS-BACKBOX Spare Backbox for Nano

Related products

• 

  wishlist

  Zeta ID2/REP/M Infinity ID2 Intelligent 2 Wire Full Function Repeater in Metal Enclosure

  DESCRIPTION

  The Infinity ID2 active repeater is used on an Infinity ID2 Panel.
  It is powered from the ID2 Panel, so is connected via 4 cores: 2 x power and 2 x data. Op to 8 repeaters can be connected. The first 2 repeaters can be powered from the panel. Subsequent repeaters would need an external power supply.
  Each repeater can be selectively configured to determine which commands it will send to the network. EG to allow some repeaters to reset the system, and others to not reset the system.
  Each Repeater can also be configured to run in a different language (Although any device labels entered by the installer will just be in the language entered)

  Read more
• 

  wishlist

  C-TEC CFP Standard 4 Zone Conventional Fire Alarm Panel Part No. CFP704-4

  ₦73,000.00

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB)
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry
  • Manufactured by C-TEC in the UK
  • Eight detector zone circuits
  • Four conventional sounder circuits
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU
  • Wide range of test and fault-finding facilities
  • Four open-collector outputs (Fire, Fault, Remote and Reset)
  • ‘Class change’ and alert inputs
  • Installer-friendly design
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required
  • Low 25mA quiescent current
  • Multiple indicators
  • No system expansion connections
  • Fully compatible with C-TEC’s ActiV range of conventional fire detectors

  Add to cart
• 

  wishlist

  C-TEC CFP Standard 8 Zone Conventional Fire Alarm Panel Part No. CFP708-4

  ₦96,000.00

  • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB)
  • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry
  • Manufactured by C-TEC in the UK
  • Eight detector zone circuits
  • Four conventional sounder circuits
  • Integral 1.5A EN54-4/A2 compliant switch mode PSU
  • Wide range of test and fault-finding facilities
  • Four open-collector outputs (Fire, Fault, Remote and Reset)
  • ‘Class change’ and alert inputs
  • Installer-friendly design
  • Attractive flush or surface mountable plastic lid and enclosure – no bezel required
  • Low 25mA quiescent current
  • Multiple indicators
  • No system expansion connections
  • Fully compatible with C-TEC’s ActiV range of conventional fire detectors

  Add to cart
• 

  wishlist

  C-TEC EP203 Automatic Extinguisher Panel Part No. EP203

  ₦169,000.00

   

  Technical Specifications
  Approvals/certifications Certified to EN12094-1 and EN54-2 & 4 by the LPCB.
  Mains supply 230V 50/60Hz.
  Mains rated current 810mA max.
  Internal power supply 19V-28.5V (27V nominal). Ripple 7V maximum (battery fault).
  Total output current limited to 1.5A @ 230Vac continuous, 3A peak (ImaxA eq 800mA).
  Quiescent current 40mA (on mains fail). Zone quiescent 2mA max.
  Max battery size and type 2 x 12V 7Ah VRLA connected in series.
  No. of detector zone circuits 3 @ 19-28Vdc (Max. length per circuit is 250m).
  Max. devices per detector zone 20 detectors (or 32 detectors/manual call points combined).
  No. of conventional sounder circuits 3 (two x 1st stage; one x 2nd stage). Max. length per circuit is 50m).
  EOL resistor value 6800 5% Tol. 0/25W (blue, grey, red, gold).
  Max. sounder output current 3 x 200mA.
  Auxiliary relays Six: (1) Fire; (2) Local Fire; (3) Extract Fan; (4) 1st Stage; (5) 2nd Stage; (6) Fault. Volt free single pole
  changeover. Max. switch current 1A; Max. switch voltage 30Vdc. Five additional relays available via
  EP212 relay card.
  Other outputs Extinguishant release (21-28Vdc, rated at 1A for 5 mins). Programmable to delay by 0-60 seconds; to
  be active for 1-300 seconds and to flood for 60-1800 seconds.
  Auxiliary inputs Six: (1) Manual Release; (2) Flow Switch; (3) Low Pressure; (4) Mode; (5) Hold; (6) Abort. 8K-2K normal;
  1.8K-200 active; 150-0 short circuit. EOL value: 6K8 +/-5%, 0.25W.
  Indicators Multiple indicators are provided – refer to the EP203 instructions for details.
  Controls Extinguishant release (housed in yellow casing); Accessed keyswitch; Operation keyswitch (Manual
  only or Manual & Auto); Buttons for Menu; Silence internal sounder; reset panel; silence/resound
  sounders and scrolling.
  Expansion connections Yes – for up to 8 x Remote status units (2 wire RS485 + 2 wire power) and/or up to 8 x Ecomomy
  status units (2 wire power + 2 wire mode select).
  Product dimensions (mm) 439 W x 276 H x 70 D mm (back box); 467 W x 293 H x 29 D mm (lid).
  Construction & finish Metal back box; metal chassis’ plastic lid.
  IP Rating IP30.
  Weight 4.2kg (without batteries).
  Operating conditions/temperature -5°C to +40°C. Max relative humidity: 95%

   

   

  Add to cart