A fire alarm system notifies us of an emergency, to take action to protect ourselves, our employees, and the general public.
Fire detection systems identify fire early when there is still enough time for inhabitants to safely evacuate. Control actions begin while the fire is still minor, early detection helps to reduce property loss and operational disruption. Fire alarm systems transmit information about the location of the fire to emergency responders, speeding up the firefighting procedure.
Sounders go off to warn those within the building that there may be a fire. The fire alarm system could include a remote signal system. It would then notify the fire department via a central station.
-
HORING LIH NDKB1 Carbon Monoxide Detector
- Test button for alarm simulation.
- Green LED to confirm the unit is under normal operation.
- Two modes of the Alarm LED in visible and audible warning to easily identify the status.
- Three modes of the Fault LED in visible and audible warning to easily identify the causes.
- Triple-color LED display with high brightness enables viewers to easily identify the status of detector.
- A set of relay output: COM. N.O. N.C. (NDKB1)
-
HORING LIH AH QP112 1 zone Conventional Fire Alarm Control Panel
- Removable front board for easy maintenance.
- Easy-to-clean front board is able to avoid dirt attached.
- High luminance and long life span LED.
- Independent visual & audible indication for zone open/short fault.
- Independent visual & audible indication for AC power & battery fault.
- Visual & audible indication for sounder short circuit fault.
- Buzzer silence with 3-mode operation feature.
- Accurate supervision circuit for battery.
- Short circuit = Alarm feature ( selected by JUMPER applicable for manual call point w/o resistance).
-
C-TEC Single Gang Locking Jack Socket for BF320 Part No. BF320JP
- Can be used in conjunction with a BF320 vibrating pillow pad to warn the hearing impaired of a potential fire alarm or evacuation alert condition.
- Compatible with all C-TEC fire alarm and evacuation alert systems.
- Locking mini-XLR connector and plug arrangement helps prevent accidental pillow pad removal.
- Line monitored for disconnection via an internal 6k8Ω end of line resistor (selectable at the BF320JP).
- Selectable 6K8 (pillow pad) or 27K (jack socket) end of line monitoring options for fire alarm or evacuation alert system use.
- Can be used on systems with a 10-30V DC voltage range
- Fits on a standard UK 25mm back box.
-
C-TEC Remote LED Indicator Part No. BF318
- A high-quality remote LED indicator specifically designed for use in fire alarm systems.
- Incorporates a high intensity, wide-angle red LED which is clearly visible from the front of the plate when active.
- Ideal for indicating the activation of hidden or out of-sight fire detectors, etc.
- Includes a white ‘write on’ area allowing installers to add equipment locations.
- Fits on standard UK 16mm flush or surface mount back boxes.
- Download datasheet
-
C-TEC Sounder Isolator Module (max. 30 per BF365SC) Part No. BF365IM
- A fault isolating module with sounder drive capability designed to meet requirement 17.9.2c of Dutch standard NEN2575.
- BSI certified to EN54 parts 17 & 18.
- Measures just 55mm x 55mm x 16mm (will fit in the base of most conventional sounders).
- Up to 30 BF365IM modules per BF365SC controller.
- Allows low-cost, non-fire resistant sounder circuit cabling to be used when used in conjunction with our BF365SC Sounder Isolator Controller (subject to fire officer approval).
- Wiring must be made in a loop arrangement, beginning and ending at the controller.
- If a wiring fault should occur, the Module(s) nearest to the faulty section of cabling will, if needed, isolate this section. As the Modules are driven from each direction, any loss of cable integrity will have no effect on the functionality of the actual sounders.
-
C-TEC STU Mounting Plate for BF360/12 or BF560/12 12V 2A PSU Part No. BF360SP
- Facilitates the mounting of a third-party Subscriber Terminal Unit (STU) in a BF360-12 or BF560/12 12V 2A PSU.
- Finished in 1.2mm steel.
- Accessory pack includes installation instructions, mounting screws, fixing pads, cable clip and cable tie.
- Can also be used with a BF360-24 or BF560-24 1.5A 24V PSU by using an ancillary BF360BOX enclosure mounted alongside the PSU.
-
C-TEC Single Gang Surface Interface Plate, shallow (20mm) Part No. NCP-23
-
-
-
- Allows standard UK single gang plated products to be fixed to most European style back boxes (square and round variants).
- Adapts to most European fixing centres – see video for further details.
- Multiple variants available – options include single gang shallow (NCP23), single gang deep (NCP24), double gang shallow (NCP25) and double gang deep (NCP26).
- Designed to match C-TEC’s existing plastics and colours.
- Tough and durable.
- Can also be surface mounted directly to a wall.
-
-
-
-
C-TEC Single Gang Surface Interface Plate, deep (25mm) Part No. NCP-24
- Allows standard UK single gang plated products to be fixed to most European style back boxes (square and round variants).
- Adapts to most European fixing centres – see video for further details.
- Multiple variants available – options include single gang shallow (NCP23), single gang deep (NCP24), double gang shallow (NCP25) and double gang deep (NCP26).
- Designed to match C-TEC’s existing plastics and colours.
- Tough and durable.
- Can also be surface mounted directly to a wall.
-
ZETA ZIS-40 | Base for Intrinsically Safe Smoke Detector
Technical Specification
- Diameter of installation cable wires (ZIS-40; ZIS-40/W): 1mm max; n/a
- Spacing between installation holes (ZIS-40; ZIS-40/W): 63mm; 127mm
- Dimensions (ZIS-40; ZIS-40/W): Ø107 x 28.5mm; Ø112 x 26mm
- Combined height: 43mm
- Weight: 0.1kg
-
Zeta ID2/4/M Infinity ID2 Intelligent 2 Wire 4 Zone Fire Panel in Metal Enclosure
Description
Zeta Alarm Systems is proud to introduce the most
advanced
2 wire system on the market. We can now
provide
a system that gives all of the benefits associated
with
a ‘2 Wire’ installation (less cable, quicker installation,
cost savings on labour/product) and has the facility to
‘I.D.’ the devices.
The system is built on the proven communication protocol
developed by Zeta Alarm Systems and shares the same
platform as our largest, most powerful system.
The ID2 can be used for new installations, as
a retrofit for any conventional system or as a replacement for
existing
2 wire systems when the extra features are
deemed to be desirable/necessary. This is possible
because the ID2 devices sit on radial circuits, thus
making it easy to ‘upgrade’
a system with the facility to
I.D. devices without the need to re-wire.
Technical -
Tuya WiFi + GSM Home Alarm System with Home Appliance Control Function (ES-JT-10GDT)
- Model NO: ES-JT-10GDT
- Transmission Mode: Wired and Wireless Alarm
- Receive Frequency: 433MHz / 868MHz / 315MHz Optional
- Network: GSM+WiFi
- Display: 2.4 Inch TFT Screen
- Contact ID Protocol: Supported
- Back up Battery: Rechargeable 3.7V Li Battery
chat with us