Popular
-
Gent Fire Alarm System Set of Keys for Key Switch Interface and MCP
-
Gent Fire Alarm Vigilon Manual Call Point with Glass Element and Protective Cover (Excludes Back Box)
-
Cutting-Edge Velocity Zeta Aspiration Smoke Detection Fire Alarm Panel
-
GENT ADDRESSABLE FIRE ALARM 1 TO 6 LOOP CONTROL PANEL
₦5,455,000.00
-
TEXECOM VERITAS IMPAQ E BURGLAR ALARM VIBRATION DETECTOR- WHITE
₦18,500.00
Category: manual call points
Showing 1–16 of 21 results
-
Out of StockAPOLLO ADDRESSABLE FIRE ALARM DISCOVERY MANUAL CALL POINT – YELLOW 58100-927APO
₦0.00Read moreThe Manual Call Point is commonly used to manually control smoke vent systems.
- Resettable operating element
- 170° viewable LED
- Suitable for semi flush or surface mounting
- ‘Plug and Play’ terminal connections for faster wiring
- Continuity link for wiring test before commissioning
- XP95, Discovery and CoreProtocol compatible
-
-
Out of StockGent Fire Alarm Change Over Contact MCP
Read moreOur conventional manual call points are designed to provide a manual
alarm interface to conventional fi re alarm control panels. All call points
are supplied in the standard red colour and are available in semi-flush
mounting or surface mounting options. The manual call points are all with
a 470 Ohm resistor and Normally Open contact, complete with glass.
Both break glass, and resettable operating elements can be used in the
standard unit by a yellow strip on the element which becomes visible when
activated. -
Out of StockGent Fire Alarm Key Operated Manual Call Point K21SRS-01
₦0.00Read moreManual call points from Honeywell Gent are easy and safe to operate, with no hammer required. Fully compliant with EN 54-11, each point is manufactured from ABS and both have a break glass and resettable element. For areas susceptible to inadvertent operation – such as sports halls – a stronger, clear polycarbonate cover version is available.
-
Gent Fire Alarm XENS-805 Surface MCP 470 Ohms Re-settable
₦15,000.00Add to cartGent XENS-805 Surface MCP 470 Ohms Re-settable The XENS-850 Conventional Manual Call Point requires no hammer and is easy and safe to operate. Gent’s conventional manual call points are designed to provide a manual alarm interface to conventional fire alarm control panels. All call points are supplied in the standard red colour and are available …
Gent Fire Alarm XENS-805 Surface MCP 470 Ohms Re-settableRead More
-
Out of StockGent Fire Alarm XENS-829 Weatherproof Manual Call Point 470 Ohms Resistor Glass
Read moreGent XENS-829 Weatherproof Manual Call Point 470 Ohms Resistor Glass
Gent’s range of conventional manual call points are designed to provide a manual alarm interface to conventional fi re alarm control panels. All call points are supplied in the standard red colour and are available in semi-flush mounting or surface mounting options. The manual call points are all with a 470 Ohm resistor and Normally Open contact, complete with glass.
-
Gent Fire Alarm XENS-850 Flush Manual Call Point 470 Ohms Glass
₦18,500.00Add to cartGent XENS-850 Flush Manual Call Point 470 Ohms Glass
Gent conventional manual call points are designed to provide a manual alarm interface to conventional fire alarm control panels. All call points are supplied in the standard red colour and are available in semi-flush mounting or surface mounting options. The manual call points are all with a 470 Ohm resistor and Normally Open contact, complete with glass.
Both break glass, and resettable operating elements can be used in the standard unit by a yellow strip on the element which becomes visible when activated.
With the addition of a hinged transparent cover the element may be protected against accidental operation.
A specialist test key may be inserted into the bottom of the unit to lower the glass and release the micro-switch and thus a full functional test is achieved.
-
Out of StockGent Fire Alarm XENS-FLAP Replacement Mouldings and Cover Plates
Read moreGent XENS-FLAP Replacement Mouldings and Cover Plates The XENS-FLAP is a set of replacement plastic front panel flaps and metal battery cover plates for the Gent Xenex range of conventional fire alarm control panels.
-
Out of StockGent Fire Alarm XENS-MCB-4 Replacement PCB Assembly
Read moreThe Gent XENS-MCB-4 is a spare / replacement PCB assembly for use with the Gent Xenex 4 Zone Fire Alarm Control Panel. This board is an ideal replacement part for damaged or faulty Xenex panel main circuit boards
-
Out of Stock
Gent XENS-MCB-2 Replacement PCB Assembly (Fire Alarm System)
Read moreThe Gent XENS-MCB-2 is a spare / replacement PCB assembly for use with the Gent Xenex 2 Zone Fire Alarm Control Panel. This board is an ideal replacement part for damaged or faulty Xenex panel main circuit boards
-
Out of Stock
Gent XENS-MCB-8 Replacement PCB Assembly
Read moreThe Gent XENS-MCB-8 is a spare / replacement PCB assembly for use with the Gent Xenex 8 Zone Fire Alarm Control Panel. This board is an ideal replacement part for damaged or faulty Xenex panel main circuit boards
-
Out of StockINTELLIGENT MANUAL CALL POINT – YELLOW SA5900-904APO
Read moreThe Manual Call Point is commonly used to manually control extinguishant release.
- Resettable operating element
- 170° viewable LED
- Suitable for semi flush or surface mounting
- ‘Plug and Play’ terminal connections for faster wiring
- Continuity link for wiring test before commissioning
- XP95, Discovery and CoreProtocol compatible
-
Out of StockManual ‘Crack Glass’ Call Point, surface Part No. BF370R
Read more- Certified to EN54 Part 11 (LPCB/VdS).
- Unique ‘Plug & Play’ installation concept.
- Supplied with a non-breaking plastic resettable element.
- Includes a 470Ω resistor, test key and red back box.
- Anti-Tamper facility.
- Flush version (without a red back box) also available (order code BF370MFR).
-
Out of StockManual ‘Crack Glass/No Break’ Call Point, flush/surface Part No. BF370FR
Read more- Certified to EN54 Parts 11 (LPCB) and 13 (BSI).
- ‘Universal’ design combines multiple functions into one product, simplifying selection and reducing stock variants.
- Supplied with a glass AND plastic element, a 470Ω AND 680Ω resistor and a red surface mounting back box which can be optionally discarded if flush mounting.
- Quick visible alarm indication.
- Changeover contacts.
- IP24 rated.
-
Out of StockManual ‘No Break’ Call Point, surface Part No. BF370S
Read more-
- Certified to EN54 Parts 11 (LPCB) and 13 (BSI).
- Smooth-action resettable element mimics the feel of breaking glass.
- Supplied with a red back box, reset key and ‘Not in Use’ label.
- Red LED ‘alarm ring’ illuminates call point face upon activation.
- Photoluminescent operating window remains visible for up to 5 minutes.
- Note an additional BF370SFP red flush mounting plate is required if you wish to flush mount the BF370S.
- IP66 weatherproof version (order code BF370S/W) also available.
-
Know Us
Safetech.hub is the newest online platform envisioned to provide 24/7 online platform for integrators, installers, and end users of Extra Low Voltage (ELV) systems in Nigeria
Read More
