Welcome to Safe Tech Hub

Cart

Your Cart is Empty

Back To Shop

Gent Fire Alarm Vigilon Plus 1-4 Loop Fire Alarm Addressable Control Panel with 1 Loop Card

2,579,000.00

Compare

Gent Vigilon Plus 1-4 Loop Control Panel with 1 Loop Card

Vigilon Plus Control Panels are available in 3 sizes managing 2, 4 or 6 loops each accommodating up to 200 devices including advanced fire sensors, interfaces, call points, alarm sounders and visual alarms. The Compact Plus 2 loop panels and Vigilon Plus 4 loop panels are available with integrated 24 hour standby and the 6-loop panel has full 72 hr standby capacity.

Advanced networking options allow networking of up to 200 panels in a multi-domain structure with options of copper or optic fibre connections. Vigilon’s back-lit LCD display presents clear indication of Fire or Fault location and the control panel’s innovative 8-line x 40-character display with push-button keypad is simple to use. Fire Plans can be tailored to precisely meet site requirements. Vigilon’s software allows network areas to be sectored to evacuate or alert status or configured with pre-set delays.

Fully compatible with Honeywell Gent’s innovative S-Quad range – a combined Multi-Sensor range with speech, sounder and EN54-23 Visual Alarm devices in one intelligent unit. The Vigilon Plus Repeat control panel provides full display and control of the system. Connecting to the detection loop, the repeat panel provides a cost-effective solution with minimum requirements for cabling and installation. Repeat panels are supplied complete with their own 72-hour power supply and standby batteries.

Key Features:

  • Integral EN54-4 PSU and battery standby for 24 hours (4 loop panel only)
  • Integral EN54-4 PSU for 72 hours with external batteries (6 loop panel only)
  • Vigilon’s advanced sensing technology and powerful processing in the panel quickly and identifies real fire
  • PC based commissioning tools allow complex fire plans to be configured
  • Advanced loop card technology allows for system status monitoring and diagnostics
  • The control panel has a simple user interface with LCD screen providing accurate information in an emergency
  • Multiple panel networks can be programmed seamlessly as one system, allowing for flexible design and system management
  • Flexible programming options are available at the panel
  • All Vigilon devices connect onto the same two core loop, separate sounder or repeater panel wiring circuits are not required
  • In the event of a fire or fault, Vigilon’s analogue addressable technology will provide a detailed log of events
  • Extended event log using a flash memory card

Reviews

There are no reviews yet.

Be the first to review “Gent Fire Alarm Vigilon Plus 1-4 Loop Fire Alarm Addressable Control Panel with 1 Loop Card”

Your email address will not be published. Required fields are marked *

You may also like…

  • C-TEC Fire Alarm Automatic 3+1 Extinguisher Panel Part No. EP203

    326,500.00

     

    Technical Specifications
    Approvals/certifications Certified to EN12094-1 and EN54-2 & 4 by the LPCB.
    Mains supply 230V 50/60Hz.
    Mains rated current 810mA max.
    Internal power supply 19V-28.5V (27V nominal). Ripple 7V maximum (battery fault).
    Total output current limited to 1.5A @ 230Vac continuous, 3A peak (ImaxA eq 800mA).
    Quiescent current 40mA (on mains fail). Zone quiescent 2mA max.
    Max battery size and type 2 x 12V 7Ah VRLA connected in series.
    No. of detector zone circuits 3 @ 19-28Vdc (Max. length per circuit is 250m).
    Max. devices per detector zone 20 detectors (or 32 detectors/manual call points combined).
    No. of conventional sounder circuits 3 (two x 1st stage; one x 2nd stage). Max. length per circuit is 50m).
    EOL resistor value 6800 5% Tol. 0/25W (blue, grey, red, gold).
    Max. sounder output current 3 x 200mA.
    Auxiliary relays Six: (1) Fire; (2) Local Fire; (3) Extract Fan; (4) 1st Stage; (5) 2nd Stage; (6) Fault. Volt free single pole
    changeover. Max. switch current 1A; Max. switch voltage 30Vdc. Five additional relays available via
    EP212 relay card.
    Other outputs Extinguishant release (21-28Vdc, rated at 1A for 5 mins). Programmable to delay by 0-60 seconds; to
    be active for 1-300 seconds and to flood for 60-1800 seconds.
    Auxiliary inputs Six: (1) Manual Release; (2) Flow Switch; (3) Low Pressure; (4) Mode; (5) Hold; (6) Abort. 8K-2K normal;
    1.8K-200 active; 150-0 short circuit. EOL value: 6K8 +/-5%, 0.25W.
    Indicators Multiple indicators are provided – refer to the EP203 instructions for details.
    Controls Extinguishant release (housed in yellow casing); Accessed keyswitch; Operation keyswitch (Manual
    only or Manual & Auto); Buttons for Menu; Silence internal sounder; reset panel; silence/resound
    sounders and scrolling.
    Expansion connections Yes – for up to 8 x Remote status units (2 wire RS485 + 2 wire power) and/or up to 8 x Ecomomy
    status units (2 wire power + 2 wire mode select).
    Product dimensions (mm) 439 W x 276 H x 70 D mm (back box); 467 W x 293 H x 29 D mm (lid).
    Construction & finish Metal back box; metal chassis’ plastic lid.
    IP Rating IP30.
    Weight 4.2kg (without batteries).
    Operating conditions/temperature -5°C to +40°C. Max relative humidity: 95%

     

     

    Add to cart
  • GENT ADDRESSABLE FIRE ALARM 1 TO 6 LOOP CONTROL PANEL

    6,170,000.00

    1 to 6 Loop Vigilon Plus Addressable Fire Alarm Control Panel c/w 1 loop card Battery Enclosure and 4 x 21Ah batteries (supplied in Black)   The Vigilon Plus Addressable Fire Alarm range of control panels are available in 4 loop and 6 loop versions. The 6 loop Vigilon with external batteries will support a …

    GENT ADDRESSABLE FIRE ALARM 1 TO 6 LOOP CONTROL PANELRead More

    Add to cart
  • Out of Stock

    Cutting-Edge Velocity Zeta Aspiration Smoke Detection Fire Alarm Panel ~ VDOT-ASD-100

    • Four Alarm Levels
    • 7 Relay Outputs
    • 3 in 1 Control/Display/Programmer Front PanelRS485 Network
    •  Support Modbus RTU Open Protoc
    Read more
  • C-TEC CFP Standard 4 Zone Conventional Fire Alarm Panel Part No. CFP704-4

    129,500.00
    • Third-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board (LPCB)
    • Intuitive user-friendly interface with colour-coded buttons and combined keypad/keyswitch entry
    • Manufactured by C-TEC in the UK
    • Eight detector zone circuits
    • Four conventional sounder circuits
    • Integral 1.5A EN54-4/A2 compliant switch mode PSU
    • Wide range of test and fault-finding facilities
    • Four open-collector outputs (Fire, Fault, Remote and Reset)
    • ‘Class change’ and alert inputs
    • Installer-friendly design
    • Attractive flush or surface mountable plastic lid and enclosure – no bezel required
    • Low 25mA quiescent current
    • Multiple indicators
    • No system expansion connections
    • Fully compatible with C-TEC’s ActiV range of conventional fire detectors
    Add to cart

Cart

Your Cart is Empty

Back To Shop